Fuji NXT Placement Machine Operating Guidelines

Service

Service & Repair

Technique & Support

Hot sale product

Contact us

+86 13113860003
+86 0755-36527060
judy@joysmt.com
evan@joysmt.com
Skype:+86 13600186468
WhatsApp:+86 13600186468

Get a quote today

Get infomation of our newest
products and promotions

Technique & Support

Location : Home > Service > Technique & Support

Fuji NXT Placement Machine Operating Guidelines

Time: 2015-09-29 11:28:49 Source by: www.gladsmt.com

Fuji NXT Placement Machine Operating Guidelines

1. Introduction to safety knowledge
(1) When performing machine operation, the hand and other parts of the human body cannot be placed in the gap of the module.
(2) When the machine is working, the eyes cannot be seen inside the machine. The light emitted by the camera is too strong and may affect vision.

2. Machine panel introduction
(1) START: Start NXT module action
(2) STOP: Stop after completing the board patch in the current module
(3) POWER: wake up the module / press 4 seconds to enter sleep mode
(4) OK: Confirm and execute the selected operation
(5) CANCEL: Cancel the panel operation or input data, or turn off the buzzer that is ringing
(6) GROUP: Operating several modules at the same time
(7) READY ON: Clear the alarm status of the machine
(8) CYCLE STOP: Stop after completing the current working cycle
(9) MANUAL: Switch between manual mode and operation wizard screen
(10) MONITOR: Switch between operation panel and image processing screen
(11) EMERGENCY: Emergency stop
(12) 4 arrow keys: Change the position of the cursor on the screen
(13) STANDBY: Lights up when the module has power supply

3. Display area description (In the normal state, the display area of the machine is introduced)
A. Machine status display area: In addition to the module number, the production status of the machine is also displayed.
B. Job Wizard Display Field: Display the machine's status or operation requirements, job guide when changing lines or maintenance.
C.Job display field: display the job name in units of each channel of the transport track, whether there is a circuit board, the number of production boards, etc.

4. Introduction to machine module operation
1) Power on operation
a) Check if the emergency 松开 is released, if the safety door is closed, turn on the main power switch of the machine to ON, the machine will automatically start detection, and then enter sleep mode after completion.
Press the POWER button on the operation panel, a module of the machine is woken up. If you press the GROUP and POWER buttons on the operation panel of one of the modules at the same time, the machine will wake up.
Note: After the power is turned off and the power is turned off, if you need to turn it on again, you must wait for more than 30 seconds before you can turn it off. If it is not normal, you must turn it on for 3 minutes. After each time you enter the sleep mode, do not wake up the machine immediately.

2) Shutdown operation
a) Go back to the main screen and press the POWER button on the operation panel of the module (the button in the picture) for about 4 seconds, the module enters the sleep mode; if you press one of the modules at the same time The GROUP and POWER buttons on the panel take about 4 seconds and the machine goes into sleep mode.
b) Then cut off the main power switch of the machine.

5. SMT Production

1) Transfer program: This action is handled by the technician.
2) Prepare the material and Feida: According to the station position set in the loading table, the installation fly reaches the specified station (installation operation as shown below)
3) Eliminate the alarm information of each station.
Tip: Please tap the button of the station to eliminate the alarm, it is easy to damage, pay attention to the number of steps of the material, can not be set wrong (see the right picture below)
4) Press the START button (the button in the picture) to start production.

6. Stop and re-run the machine: There are 3 ways to stop the NXT in production.
1) Circuit board discharge operation: The NXT stops after the board is being mounted.
2) Cycle stop: NXT stops according to the action cycle
3) Emergency stop: NXT stops immediately

7. Daily cleaning
1) Cleaning waste belt recycling bin: Empty the waste tape box of each module and put it back flat.
2) Clean the flying box: Pull out the module according to the operation, take out the flying box, empty the flying material, and put it back.
note:
a) Only one module can be dragged at a time.
b) When returning the flying box, it must be flattened and cannot exceed the plane of the camera.

3) 6S on the periphery of the machine
4) Dragging out the module during daily cleaning
(a) the machine is at a standstill;
(b) Press the MANUAL button and the following screen appears;
(c) Select the picture to be cleaned and press the OK button;
(d) When you press the START button, the module will pop up automatically.
(e) Then hold the handle of the module and pull out the module.

Prev : Fault solution for FUJI Placement Mchine

Next : Best Practices Reflow Profiling for Lead-Free SMT Assembly